插装式液控能源选择阀的设计与分析

针对液压系统油源的安全性及可靠性问题，提出油源冗余设计方法，即多油源供给多负载，当某一油源发生故障时能源选择阀切断故障油源，由其他油源给负载提供基本液压能源，系统能完成必须的服役性能。针对液压系统能源选择阀存在的频繁换向与振动问题，提出一种插装式液控能源选择阀，其先导阀采用锥阀和可变阻尼形式，主阀采用三台肩且终端有缓冲功能的滑阀。建立了插装式液控能源选择阀的数学模型，分析了能源选择阀在两种模拟故障下的切换压力及切换时间、油源压力脉动等特性。理论分析结果表明，油源压力阶跃和线性变化时，某能源选择阀切换时间分别为5 ms和7 ms。当压力发生波动时，主阀不会发生振动，还可通过液控先导阀结构设计来控制切换压力和回复压力大小。     

非线性能量阱对飞轮振动抑制效果的实验研究

利用薄片金属梁作为非线性刚度元件，构建一种非线性能量阱。为了验证非线性能量阱对飞轮振动特性的抑制效果，搭建地面飞轮测试系统。分别采用力锤敲击和飞轮以恒定转速运行的方法施加不同载荷，对安装非线性能量阱前后测试系统各典型位置的振动响应进行对比研究。利用实测数据，采用傅里叶变换方法将动态响应信息分别在时间域和频率域内展开。研究表明：力锤敲击产生的冲击载荷和飞轮以恒定转速运行产生的稳态载荷均可以激发非线性能量阱定向能量传输；受非线性能量阱的影响，柔性支架设备安装面和飞轮安装面振动响应得到有效抑制。但是，由于非线性能量阱阻尼和吸振子质量较小，不同程度削弱了其振动抑制效果。     

基于HHT的航空直流串行电弧特征提取方法

由于飞机内部布线空间有限、电弧故障存在发生时间地点随机以及特征不明显等问题，导致检测困难。本文基于航空270 V高压直流（HVDC）系统开展直流串行电弧故障特征提取方法研究，采用希尔伯特黄变换（HHT）提取电弧电流交流分量的时域和频域特征量。选择HHT的固有模态函数IMF5瞬时幅值的峰峰值和标准差作为识别电弧故障的时域特征，与原始信号中提取的时域特征量对比，正常和电弧特征量的区分度更大；选择HHT的固有模态函数IMF1+IMF2、一定频带范围内的瞬时幅值计算得到的谐波功率和作为区分正常和电弧情况的频域特征量。与常用的快速傅里叶变换（FFT）方法相比，HHT三维时频谱能够反映信号的局部特征，HHT方法计算得到的正常和电弧特征量之间的区分度更大，电弧和正常特征量的比值最高可达346。基于HHT的电弧故障特征提取方法能够更好地区分正常和电弧情况，有助于提高电弧故障的检测率，降低虚警率，具有重要的工程应用价值。     

飞行器程控跟踪相控阵天线安装误差补偿技术

针对窄波束高增益相控阵天线波束指向精度要求高、安装误差对波束指向的影响无法忽略的问题,提出了一种基于光学瞄准的安装误差测量方法,给出了光学测量内容和误差修正矩阵,经某型无人机飞行测试表明,该方法可以减少由安装误差带来的波束指向偏差,对高精度波束指向具有重要意义。     

Backstepping sliding-mode control of stratospheric airships using disturbance-observer

In the presence of unknown disturbances and model parameter uncertainties, this paper develop a nonlinear backstepping sliding-mode controller (BSMC) for trajectory tracking control of a stratospheric airship using a disturbance-observer (DO). Compared with the conventional sliding mode surface (SMS) constructed by a linear combination of the errors, the new SMS manifold is selected as the last back-step error to improve independence of the adjustment of the controller gains. Furthermore, a nonlinear disturbance-observer is designed to process unknown disturbance inputs and improve the BSMC performances. The closed-loop system of trajectory tracking control plant is proved to be globally asymptotically stable by using Lyapunov theory. By comparing with traditional backstepping control and SMC design, the results obtained demonstrate the capacity of the airship to execute a realistic trajectory tracking mission, even in the presence of unknown disturbances, and aerodynamic coefficient uncertainties.     

一种电离层TEC格点预测模型

基于分析时间序列数据的门限控制单元（GRU）神经网络模型，利用电离层TEC网格点历史数据、太阳活动指数、地磁活动指数作为预测因子，提出一种高精度电离层TEC格点预测模型.对全球60个网格点的数据进行了模型预测和对比实验，得到北半球平均相对精度的均值为83.96%，高于南半球的73.60%，表明预测模型在北半球的适应性更好，且中低纬地区的适应性优于高纬地区；预测模型在磁扰动期的平均相对精度的均值比磁平静期平均相对精度的均值高，约1.95%；与基于递归神经网络（RNN）、长短时记忆网络（LSTM）和双向长短时记忆网络（Bi-LSTM）的电离层TEC单站预测模型相比，本文预测模型的均方根误差（RMSE）平均为原来的80.8%.      

SiC/CVD SiC复合涂层的抗氧化及抗热震性能研究

为了提高C/SiC复合材料耐高温性能,采用泥浆浸渍裂解与真空化学气相沉积(CVD)在材料表面制备了SiC/CVD SiC复合涂层,通过XRD、SEM分析了涂层组成与结构;研究了复合涂层的高温抗氧化(700～1 500℃)和抗热震性能。结果表明,泥浆浸渍法制备的SiC涂层具有一定的封孔效果,可使材料开孔率下降,但高温抗氧化效果并不佳,1 200℃氧化10 min后材料弯曲强度保留率下降明显仅有86%。CVD SiC涂层结构致密,与SiC封孔涂层结合较好,在700～1 500℃具有较好的抗氧化效果,随着氧化温度的升高,氧化后涂层完好,表面O元素逐渐增加,材料失重率缓慢增加但不大于0.5%,且材料性能并未下降。涂层材料在1 200℃-10 min短时热震5次后材料弯曲强度保留率仍有95%以上,且未出现开裂、剥落等热震损伤。在1 200℃-30 min长时热震10次后,涂层材料基本被完全氧化,材料失去保护作用,弯曲强度下降至90%左右。     

A new dynamic pushback control method for reducing fuel-burn costs: Using predicted taxi-out time

Long departure-taxi-out time leads to significant airport surface congestion, fuel-burn costs, and excessive emissions of greenhouse gases. To reduce these undesirable effects, a Predicted taxi-out time-based Dynamic Pushback Control(PDPC) method is proposed. The implementation of this method requires two steps: first, the taxi-out times for aircraft are predicted by the leastsquares support-vector regression approach of which the parameters are optimized by an introduced improved Firefly algorithm. Then, a dynamic pushback control model equipped with a linear gate-hold penalty function is built, along with a proposed iterative taxiway queue-threshold optimization algorithm for solving the model. A case study with data obtained from Beijing International airport(PEK) is presented. The taxi-out time prediction model achieves predictive accuracy within 3 min and 5 min by 84.71% and 95.66%, respectively. The results of the proposed pushback method show that total operation cost and fuel-burn cost achieve a 14.0% and 21.1%reduction, respectively, as compared to the traditional K-control policy.(3) From the perspective of implementation, using PDPC policy can significantly reduce the queue length in taxiway and taxi-out time. The total operation cost and fuel-burn cost can be curtailed by 37.2% and 52.1%,respectively, as compared to the non-enforcement of any pushback control mechanism. These results show that the proposed pushback control model can reduce fuel-burn costs and airport surface congestion effectively.